F-GA4 FUEL DISPENSER

F-GA4 FUEL DISPENSER

Pump Type: Optional

Inlet Pressure :>=54kPa.

Flow rate (L/min.) :55±5

Suction Distance (m) :6(verticalmente) / 50(orizzontalmente)

FlowMeter Type : Optional

Accuracy :±0.2%

Motor :Voltage(V) 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type: Solenold Vale Control Type

Preset :Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional :Display Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price: 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight :350kg

Dimension(L×W×H) :1660*660*2190(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 17

but also container, vacuum pump. The hose made according to GB10543 consists of inner rubber layer, enhancing layer, conductible metal line and exterior rubber layer. Whichever hose abided by the requirements of GB/T9081-2001 Fuel dispenser for vehicle and JJG443-98 Fuel Dispenser in terms of safety and accuracy. During operation pay much attention to protect hose: avoid as much crook as possible; prevent pressure on hose; avoid and reduce abrasion with ground. 4. Connection and seal about pipeline and hydraulic elements Each part of fuel dispenser adopts pipeline connection, dividing into hard type and soft type. In hard type con fuel dispenser nection steel pipe, brass pipe and aluminum pipe are adopted as pipeline, but in soft type one hose and corrugated pipe. Connected components includes relative elbow jointer, flange and directive jointer. There are following seal types: cone-shaped seal, subulate thread seal, O-ring seal, rubber and asbestos gasket, cork and rubber board, engineering rubber board. According to regulation stipulated in GB/T9081 every fuel dispenser should be conducted sealability testing before leaving factory, no leakage found under normal operation. As replace some parts or found leakage these problems should be paid attention: Cone-shaped seal structure Cone-shaped seal structure also called as expanding jointer, which is composed of pipe with outstretched end, flat spout and outside thread bushing. Sealability is ensured through tightly integration of subulate surfaces. In disassembling or reassembling cone-shaped seal structure pays much attention not to hurt or broken sublatae surfaces, cleaning waste. Thread airproof As disconnection or reassembly thread surface should be kept clean, daubing seal glue or seal belt before installation. O-ring seal Most manufacturers adopts national standard to design O-ring seal, reaching a good fuel dispenser sealability. However, some parts is impossi fuel dispenser ble to adopt national standards because of specific structure. Thus, user should purchase or employ appropri

Date :　　 POS Department　　 9. EXCHANGE PROTOCOL　　 This protocol enables:　　 Establishment of the logical link between applications:　　 management of the maintenance of this link　　 fuel dispenser general validation of application messages　　 9.1. Procedure for logical establishment of communications　　 Includes the following issues:　　 Set-up of the logical channels between the corresponding monetics applications　　 synchronisation of application software and applications:　　 �? compatibility check of application software　　 �? consistency check of the parameterisation between the corresponding monetics　　 applications　　 The following diagram summarises the exchanges of this procedure as detailed in the　　 fuel dispenser followin fuel dispenser g paragraphs:　　

lmost twice as much as at this stage in 2005. Consolidation is happening in sectors from steel to supermarkets, food to finance. Until recently, the focus was on cross-border transactions, both into and out of China. But for financiers, a more promising area may well be the domestic market. There, financial reforms have encouraged companies to follow what firms elsewhere in the world are doing, partly in response to China merging to protect profits, pricing power and market share. To an extent, the country is being dragged along in the wake of a global boom in M&A, but financial deregulation is also helping. This month marks the fuel dispenser first anniversary of reforms allowing companies to convert non-tradable shares (on average, still two-thirds of the total for listed Chinese companies) into ordinary shares—which can then be more easily sold to potential bidders. The reforms have led to a sharp rise in domestic share prices, boosting management confidence and prompting a flood of initial public offerings—worth 40 billion yuan ($5 billion) so far in 2006. A new rule on September 1st will allow bidders for a listed company to take control without having to buy out minorities. A proposal to allow domestic firms to finance mergers with equity and assets as well as cash is also likely to encourage M&A, if approved. The most eye-catching deals are still the daring attempts by Chinese firms to buy overseas. State-owned oil and minerals giants, flush with cash and assured of government support, have been hunting raw materials for years. Last month China National Petroleum Corporation, the parent of PetroChina, took a $500m stake in Rosneft, the Russian oil group, having paid $4.2 billion for PetroKazakhstan, a Central Asian refiner, last year. So far this year, Chinese companies have spent $9.3 billion on overseas acquisitions, against $2.3 billion in th fuel dispenser e same period last year. Yet, despite deep fuel dispenser pockets, mainland firms have not had it all their own way. CNOOC, an oil producer, withdrew a $19 billi